Is a Fire Performance Solution Worth It for Your Project?

Last Updated: November 21, 2026

Quick Summary

A fire performance solution is worth it when your building design does not suit the standard NCC deemed-to-satisfy rules, such as an unusual layout or large atrium. It is usually more costly and slower to approve than a standard route, so it only pays off where the design flexibility delivers a real project benefit.

  • Choose a performance solution when a feature like a large atrium or unusual façade falls outside the standard rules.
  • If a modest layout change would meet the deemed-to-satisfy provisions, redesign is often faster and cheaper.
  • Engage the fire engineer at concept design, when changing direction costs least.
  • Cheapest quotes can cost more if a thin submission triggers repeated requests and programme delay.
  • Approval depends on the certifier or fire authority accepting your assumptions and evidence, so check local requirements early.

Table of Contents

What a Fire Performance Solution Actually Is

A fire performance solution is an alternative way to show a building meets the fire safety intent of the National Construction Code (NCC) when the standard prescriptive provisions do not suit a building design. Rather than following the set rules, a fire engineer builds a case showing the design achieves the required level of safety.

Many designs that look unusual on paper still fit the deemed-to-satisfy rules once the layout is reviewed carefully.

Performance solutions tend to appear where a building has an unusual layout, a large open atrium, a non-typical façade, or a mix of uses that the prescriptive rules were never written for. In those cases, a Australian Building Codes Board guidance on the NCC framework allows the designer to justify a different route to the same outcome.

Watch out: a performance solution is not a shortcut. It needs documented assumptions, fire scenarios and evidence, and it still has to be accepted by the approval authority.

Performance Solution vs Deemed-to-Satisfy: Which Route Fits Your Building

Deemed-to-satisfy (DTS) provisions are the fixed rules in the NCC. If your building meets them, approval is usually straightforward because the route is already accepted. A performance solution is the alternative route, and it is judged against the performance requirements rather than the specific rules.

FactorDeemed-to-SatisfyPerformance Solution
Approval pathFollows set rulesRequires engineering justification
Design flexibilityLimitedHigh
Upfront engineering effortLowerHigher
Approval certaintyGenerally higherDepends on evidence and assessor
Best suited toStandard buildingsComplex or non-standard designs

For a standard warehouse or a simple residential building, DTS is usually the cheaper and faster path. For a building with a feature the rules did not anticipate, a performance solution may be the only practical way forward.

How Much a Fire Performance Solution Costs and What Drives the Fee

Pricing for a fire performance solution depends on the project, so it is worth understanding the cost drivers before comparing fees against the design savings and programme benefits the solution might unlock.

The main cost drivers are:

  • Number of fire scenarios. A solution that models one or two design fires costs less than one that tests smoke spread, evacuation and structural response across multiple scenarios.
  • Building geometry and complexity. Large atriums, irregular floor plates, multi-storey voids and complex façades take more modelling time than a simple rectangular layout.
  • Number of performance requirements in scope. A solution addressing a single non-compliance is narrower than one covering egress, fire spread, smoke control and structural fire resistance together.
  • Evidence and modelling method. Advanced computational modelling and peer review add cost but may reduce approval risk.
  • Approval rounds. Each revision after certifier or fire authority feedback adds engineering time. A clear, complete submission at the first pass is cheaper than a drawn-out review cycle.
  • Coordination with the design team. Solutions that require changes to architecture, services or egress layouts carry design costs beyond the fire engineer’s fee.

A practical way to judge value is to compare the fee against what the alternative would cost. If meeting the deemed-to-satisfy provisions would require removing a feature the project depends on, a full-height atrium, a particular facade, a heritage element, the performance solution may be cheaper than redesign. If a modest layout change would satisfy the standard rules, the engineering fee is likely an unnecessary cost.

Watch out: the cheapest quote is not automatically the best value. A low fee that produces a thin submission can lead to repeated requests for information, redesign and programme delay, which usually costs more than a thorough first submission.

NCC Fire Performance Solution Examples From Real Project Types

Performance solutions commonly appear in a handful of project types. Large atriums and open-plan spaces often need a solution because smoke spread and evacuation behave differently from the rules’ assumptions. Facades with unusual cladding or setbacks are another common case, where the question is how fire spreads across the external wall.

Mixed-use buildings with several classes of occupancy under one roof are also frequent candidates. The solution then shows how the separation and egress arrangements still protect each occupant group.

For each example, the same logic applies. The engineer identifies the performance requirement, defines the fire scenarios, and demonstrates that the design meets the intent. Liaising with the architect, builder and certifier early helps address each issue in the solution.

Approval Requirements You Must Meet Before Construction

Before construction begins, a performance solution needs to be accepted. The building surveyor or certifier must be satisfied that the solution meets the NCC performance requirements. In some states, the fire and rescue authority must also be consulted.

Building surveyor and fire engineer reviewing a fire performance solution process on site plans
Building surveyor and fire engineer reviewing a fire performance solution process on site plans

Acceptance still depends on a complete and clear submission. Check the requirements of your local approval authority at the start, as the documentation expected can vary by jurisdiction.

Risks, Delays and Reasons a Performance Solution May Not Pay Off

The value question is really a risk question. A performance solution can unlock a design that the standard rules would otherwise block, but it also introduces approval uncertainty and programme exposure that a deemed-to-satisfy path usually avoids. Understanding where those risks sit helps you decide whether the flexibility is worth it.

The main risks are:

  • Approval uncertainty. The certifier or fire authority must be satisfied the solution meets the NCC performance requirements. If they do not accept the assumptions or evidence, the design may need to change.
  • Programme delay. A rejected or queried solution late in the project can hold up construction. The later the engagement, the greater the exposure.
  • Ongoing obligations. Some solutions carry conditions that must be maintained through construction and operation, such as specific maintenance regimes or management-in-use requirements.
  • Coordination risk. A solution often depends on other consultants’ assumptions, facade performance, mechanical smoke control, egress modelling, and gaps between disciplines can undermine the case.

A staged timeline makes the decision points clearer:

  1. Concept design. Engage the fire engineer early to confirm whether a performance solution is needed and which performance requirements are in scope. This is the cheapest point to change direction.
  2. Schematic design. Define the fire scenarios, assumptions and evidence strategy, and confirm them with the certifier before detailed documentation.
  3. Documentation. Prepare the performance solution report and supporting modelling. Incomplete documentation here is the most common cause of review delays.
  4. Approval. Submit to the certifier and, where required, the fire authority. Build in time for at least one round of queries.
  5. Construction. Maintain the assumptions and conditions through construction, and hand over any ongoing obligations.

There are clear cases where a performance solution may not pay off. If a modest layout change would bring the building within the deemed-to-satisfy provisions, redesign is often faster, cheaper and more certain than an engineered solution. The same applies where the non-compliance is marginal or where the approval authority is known to take a conservative view of the proposed method.

Watch out: choosing the performance route out of habit, rather than because the building genuinely needs it, is a common and expensive mistake. The added engineering cost and approval effort only make sense when the design flexibility delivers a real project benefit.

Deciding Whether to Commission a Performance Solution for Your Project

Start by asking whether your building fits the standard rules. If it does, the deemed-to-satisfy route is usually the simpler option. If it does not, and the design depends on a feature the rules do not cover, a performance solution may be worth the investment.

A short conversation about your building can help establish whether a solution is needed and what it will involve. Send an enquiry to get a clear view of the options for your project.

Frequently Asked Questions

What is a fire performance solution?

A fire performance solution is an alternative way to show that a building meets the fire safety performance requirements of the National Construction Code (NCC) when the standard Deemed-to-Satisfy provisions do not suit the design. A fire engineer analyses the proposed building, identifies the fire safety objectives, and demonstrates with evidence that those objectives are met. It is used most often for complex, large or non-standard buildings, where following the prescriptive rules would limit the design or be impractical. The solution is then assessed by the approval authority before construction proceeds.

When does a building project need a fire performance solution?

A project usually needs a fire performance solution when it cannot comply with the Deemed-to-Satisfy provisions of the NCC, or when following them would significantly restrict the design. Common triggers include atriums, large open-plan spaces, unusual egress layouts, and buildings with heights or occupancies outside standard limits. Early identification matters. Speaking with a fire engineer during concept design usually avoids costly redesign later, because the non-compliances can be flagged before the architecture is locked in.

Is a fire performance solution cheaper than a Deemed-to-Satisfy design?

Not necessarily. A performance solution adds engineering fees, so it is usually a cost in its own right. Its value lies in what it avoids: redesign, loss of floor area, or expensive physical fire protection measures that a prescriptive design would require. Whether it saves money depends on how far the standard provisions are from the design you want. Pricing depends on project complexity, scope and timing, so request a quote from FyreWise for a figure specific to your project.

What information should I provide to a fire engineer before requesting a quote?

Provide the current architectural drawings, the building classification, the storey count and floor areas, the intended occupancy and occupant numbers, and a short description of the feature you want to justify. Note any Deemed-to-Satisfy provisions you believe cannot be met. At FyreWise, a brief, concise description is often enough to identify the issue, and we can advise what is needed to reach compliance before producing a report. Include your target programme so timing can be planned.

Leave a Comment

Your email address will not be published. Required fields are marked *

Scroll to Top